Category: Softwares

Many BIOS manufacturers have provided backdoor passwords that can be used to access the BIOS setup in the event you have lost your password. These passwords are case sensitive, so you may wish to try a variety of combinations.

WARNING: Some BIOS configurations will lock you out of the system completely if you type in an incorrect password more than 3 times. Read your manufacturers documentation for the BIOS setting before you begin typing in passwords.

ALFAROME		BIOSTAR		KDD		ZAAADA
ALLy		CONCAT		Lkwpeter		ZBAAACA
aLLy		CONDO		LKWPETER		ZJAAADC
aLLY		Condo		PINT		01322222
ALLY		d8on		pint		589589
aPAf		djonet		SER		589721
_award		HLT		SKY_FOX		595595
AWARD_SW		J64		SYXZ		598598
AWARD?SW		J256		syxz
AWARD SW		J262		shift + syxz
AWARD PW		j332		TTPTHA
AWKWARD		j322
awkward

AMI		BIOS		PASSWORD		HEWITT RAND
AMI?SW		AMI_SW		LKWPETER		CONDO

phoenix

PHOENIX

CMOS

BIOS

ALFAROME		BIOSTAR		biostar		biosstar
CMOS		cmos		LKWPETER		lkwpeter
setup		SETUP		Syxz		Wodj

Manufacturer	Password
VOBIS & IBM	Merlin
Dell	Dell
Biostar	Biostar
Compaq	Compaq
Enox	xo11nE
Epox	Central
Freetech	Posterie
IWill	Iwill
Jetway	Spooml
Packard Bell	bell9
QDI	QDI
Siemens	SKY_FOX
TMC	BIGO
Toshiba	Toshiba

Most Toshiba laptops and some desktop systems will bypass the BIOS password if the left shift key is held down during boot

Press both mouse buttons repeatedly during the boot

Many motherboards feature a set of jumpers or dipswitches that will clear the CMOS and wipe all of the custom settings including BIOS passwords. The locations of these jumpers / dipswitches will vary depending on the motherboard manufacturer and ideally you should always refer to the motherboard or computer manufacturers documentation. If the documentation is unavailable, the jumpers/dipswitches can sometimes be found along the edge of the motherboard, next to the CMOS battery, or near the processor. Some manufacturers may label the jumper / dipswitch CLEAR – CLEAR CMOS – CLR – CLRPWD – PASSWD – PASSWORD – PWD. On laptop computers, the dipswitches are usually found under the keyboard or within a compartment at the bottom of the laptop.

Please remember to unplug your PC and use a grounding strip before reaching into your PC and touching the motherboard. Once you locate and rest the jumper switches, turn the computer on and check if the password has been cleared. If it has, turn the computer off and return the jumpers or dipswitches to its original position.

The CMOS settings on most systems are buffered by a small battery that is attached to the motherboard. (It looks like a small watch battery). If you unplug the PC and remove the battery for 10-15 minutes, the CMOS may reset itself and the password should be blank. (Along with any other machine specific settings, so be sure you are familiar with manually reconfiguring the BIOS settings before you do this.) Some manufacturers backup the power to the CMOS chipset by using a capacitor, so if your first attempt fails, leave the battery out (with the system unplugged) for at least 24 hours. Some batteries are actually soldered onto the motherboard making this task more difficult. Unsoldering the battery incorrectly may damage your motherboard and other components, so please don’t attempt this if you are inexperienced. Another option may be to remove the CMOS chip from the motherboard for a period of time.
Note: Removing the battery to reset the CMOS will not work for all PC’s, and almost all of the newer laptops store their BIOS passwords in a manner which does not require continuous power, so removing the CMOS battery may not work at all. IBM Thinkpad laptops lock the hard drive as well as the BIOS when the supervisor password is set. If you reset the BIOS password, but cannot reset the hard drive password, you may not be able to access the drive and it will remain locked, even if you place it in a new laptop. IBM Thinkpads have special jumper switches on the motherboard, and these should be used to reset the system.

Boot to MS- DOS prompt, run through the below example, this example is perfectly fine to run on any PC Computer running MS-DOS / Windows and will not harm anything.

DEBUG script that will just reset the password only
Type debug and press enter.   (ex.  A:\>debug )
After typing debug you will get “-” as a prompt ,type these exactly how they are written.
o 70 10
o 71 20
quit
Explanation of code:
DEBUG    ; Run DEBUG, “-” will appear on each line then type:
o 70 20     ; Send 70 to address 18
o 71 21     ; Send 71 to address FF
q              ; Quit DEBUG
or you can use this alternate DEBUG script that will just reset the the BIOS
A
MOV AX,0
MOV AX,CX
OUT 70,AL
MOV AX,0
OUT 71,AL
INC CX
CMP CX,100
JB 103
INT 20
Note: Nothing is typed on this line
G By pressing G this will execute the above script
Q

CmosPwd by CGSecurity – This is probably the most up to date and popular CMOS decryption tool. CmosPwd decrypts password stored in cmos used to access BIOS SETUP, you can also backup, restore and erase/kill cmos.You will have to be logged in as administrator, run ioperm -i command and then run cmospwd_win.exe
PC CMOS Cleaner – PC CMOS Cleaner is an easy-to-use tool to recover, delete, decode and display the superior passwords stored in BIOS whatever the brand is. It’s an bootable CD that runs on x86 and x86_64 computers. It can display the superior passwords of the BIOS, remove BIOS password(will set the BIOS to default status, need reset date).